After a workshop in Kuopio held in June 2006, Interbull decided to go forward with the development of a system for beef international genetic evaluation and a three year project called Interbeef was launched in June 2007. The participating countries are so far limited to Europe and the only trait evaluated at present is adjusted weaning weight (weight at 200 days). The results from a first international genetic evaluation have been shared with the countries but are not yet official. The evaluation is based on data from purebred Charolais and Limousin. To achieve good estimates of proofs in an international context it is important that methods for Data validation and model selection are implemented.

This masters thesis concerns a modeling project performed at Volvo Technology in Gothenburg, Sweden. The main purpose of the project has been to develop a physical model of the climate in construction vehicles that later on can be used in the development of an electronic climate controller. The focus of the work has been on one type of wheel loader and one type of excavator. The temperature inside the compartment has been set equal to the notion climate. With physical theories about air flow and heat transfer in respect, relations between the components in the climate unit and the compartment has been calculated.

The stakeholders for requirements elicitation need to be identified at an early stage and their knowledge is the basis for what is to become a requirements specification. Just because a stakeholder holds a lot of expertise and knowledge it does not mean that the stakeholder can communicate the knowledge in a clear way. Validation of knowledge means that knowledge is valued and recognized in a structured way. People and organizations can evolve by exchanging knowledge, experience and skills.  The purpose of this study is to increase the understanding of knowledge management between requirement elicitation and external stakeholders.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

Since energy simulations are used to verify that projected residential buildings will reach the current energy requirements it is important that the results are reliable.This report investigates the extent of uncertainty in energy simulations, estimates the causes of the uncertainty and its economic and environmental consequences.The method used in this report is based on three validation methods; empirical validation, analytical validation and comparative validation. The analysis was carried out for five multi-family dwellings in Uppsala with installed meters for energy measurements. One of these objects, Klockarlunden, was studied in more detail than the others.The results show that the deviations are between 10 and 29% for the studied objects, which means that the uncertainty is estimated to be at least 29%. All simulations underestimate the buildings need of energy. The simulation for Klockarlunden can predict the energy consumption to be within the range of 46-98 kWh/m2year with 90% confidence level based on the current uncertainty.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

Information regarding cows grazing behaviour and time spent grazing can be of great interest to dairy farmers, since this information can indicate how well suited the pasture is to the cows. Feed intake at pasture is however challenging to measure. Automated systems for monitoring the behaviour of cows within dairy production have become increasingly important and relatively common. The aim of this study was to validate an activity measuring device (HOBO® G Logger Pendant Data Logger, USA), a triaxial accelerometer that registers the cow?s head positions during grazing, in order to see if cows? grazing behaviour on pasture could be distinguished from their non grazing behaviour.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

This thesis describes new methods for automatic crack detection in pavements. Cracks in pavements can be used as an early indication for the need of reparation.Automatic crack detection is preferable compared to manual inventory; the repeatability can be better, the inventory can be done at a higher speed and can be done without interruption of the traffic.The automatic and semi-automatic crack detection systems that exist today use Image Analysis methods. There are today powerful methods available in the area of Computer Vision. These methods work in higher dimensions with greater complexity and generate measures of local signal properties, while Image Analyses methods for crack detection use morphological operations on binary images.Methods for digitalizing video data on VHS-cassettes and stitching images from nearby frames have been developed.Four methods for crack detection have been evaluated, and two of them have been used to form a crack detection and classification program implemented in the calculation program Matlab.One image set was used during the implementation and another image set was used for validation. The crack detection system did perform correct detection on 99.2 percent when analysing the images which were used during implementation.